Monday, February 22, 2010

Wood veneer, Ash (Burl)

Ash (Burl)

cat-ash-burl.jpgLarge, clean, and well-figured ash burl veneer is notoriously difficult to find. More commonly, you'll find ash burl with small dark brown knots which add a touch of "character" to the uniform creamy color. Ash burls are most often found at the trunk of the tree (as opposed to under-ground) which further indicates that the burl growth is the result of external influences such as insects, forest animals, and humans. With a vacuum press, ash burl is very easy to adhere to a substrate.
Common Name:
European Ash Burl, White Ash Burl
Scientific Name:
Fraxinus excelsior
Family:
Oleaceae
Color:
Light cream to yellow, occassional dark brown knots
Origin:
Primarily Western Europe
Hardness:
Hard
Texture:
Medium texture with interlocked grain
Finishing:
Readily accepts stains and finishes

Wood veneer, Anigre (Figured)

Anigre (Figured)

cat-anigre-curly.jpgAngire is an often overlooked beauty. Its texture is pleasing to the eye and works well projects where a subtle yet defined wood veneer is needed. Curly anigre is one of the more affordable figured veneer types despite it's relative rarity. Anigre can be found in Ghana, Cameroon, Congo, and in the rain forests of Uganda. I've had the pleasure of seeing numerous veneered projects in which the creator used anigre as a contrasting compliment to darker woods such as walnut and jarrah.
Common Name:
 Anigre, anegre, agnegre, aningeria
Scientific Name:
 Aningeria superba, Aningeria robusta
Family:
 Sapotaceae
Color:
 Creamy yellow to pale brown
Origin:
 West Africa
Hardness:
 Moderately soft
Texture:
 Smooth texture with semi-open pores
Finishing:
 Readily accepts stains and finishes

Wood veneer, Amboyna (Burl)

Amboyna (Burl)

cat-amboyna-burl.jpgThough straight grain amboyna is a beautiful wood, it is the amboyna burl that is the most sought after. Known for its interleaving colors of red, orange, brown and yellow, amboyna burl is unmistakably one of the forest's most valued species. Before a finish is applied, this veneer typically develops a white crystal-like formation on the surface which is a result of the minerals in the wood cells being displaced by air. To remove the crystals, simply spray the veneer with denatured alcohol and wipe clean. Amboyna burl is often used on automotive dashboards and was the first burl veneer to be offered in Rolls Royce automobiles.
Common Name:
 Amboyna, Narra, Andaman Redwood
Scientific Name:
 Pterocarpus indicus
Family:
 Leguminosae
Color:
 Brown to reddish with occasional orange colors, sapwood is yellowish
Origin:
 Indonesia, South East Asia
Hardness:
 Primarily hard
Texture:
 Medium texture with interlocked grain
Finishing:
 Readily accepts stains and finishes

The Cuts Used to Create Veneer

Rotary Cut VeneerRotary Cut
The log is centered on a lathe and turned against a broad cutting knife set into the log at a slight angle.
  How Veneer is Rotary Cut
  Quarter Slicing VeneerQuarter Slicing
The slicing is made perpendictular to the annual growth rings of the tree. This creates a straight grain appearance
  How Veneer is cut with Quartered Slicing
   Lengthwise Slicing VeneerLengthwise Slicing
This is done from a board of flat sawn lumber rather than from a log. A variegated figure is created with this slice.
    How Veneer is cut with Lengthwise Slicing
  Plain Cut VeneerPlain Slicing
By slicing parallel to the center of the log, a raised "cathedral effect" is formed by the innermost growth rings
    
  Half-Round SlicingHalf-Round Slicing
Sliced on an arc parallel to the center of the log, this cut achieves a flat-cut veneer appearance.
    How Veneer is cut with Half-Round Slicing
  Rift Cut VeneerRift Cut
This straight grain cut is derived by slicing red and white oak at a slight angle to minimize the irregularities in the wood.
    How Veneer is Rift Cut.

Wood veneer

In woodworking, veneer refers to thin slices of wood, usually thinner than 3 mm (1/8 inch), that are typically glued onto core panels (typically, wood, particle board or medium-density fiberboard) to produce flat panels such as doors, tops and panels for cabinets, parquet floors and parts of furniture. They are also used in marquetry. Plywood consists of three or more layers of veneer, each glued with its grain at right angles to adjacent layers for strength. Veneer beading is a thin layer of decorative edging placed around objects, such as jewelry boxes.

Veneer is obtained either by "peeling" the trunk of a tree or by slicing large rectangular blocks of wood known as flitches. The appearance of the grain and figure in wood comes from slicing through the growth rings of a tree and depends upon the angle at which the wood is sliced. There are three main types of veneer-making equipment used commercially:
A rotary lathe in which the wood is turned against a very sharp blade and peeled off in one continuous or semi-continuous roll. Rotary-cut veneer is mainly used for plywood, as the appearance is not desirable because the veneer is cut concentric to the growth rings.
A slicing machine in which the flitch or piece of log is raised and lowered against the blade and slices of the log are made. This yields veneer which looks like sawn pieces of wood, cut across the growth rings.
A half-round lathe in which the log or piece of log can be turned and moved in such a way to expose the most interesting parts of the grain.
Each slicing processes gives a very distinctive type of grain, depending upon the tree species. In any of the veneer slicing methods, when the veneer is sliced, a distortion of the grain occurs. As it hits the wood, the knife blade creates a "loose" side where the cells have been opened up by the blade, and a "tight" side.
Traditionally, veneers were also sawn, but this is more wasteful of wood. Veneering is an ancient art, dating back to the ancient Egyptians who used veneers on their furniture and sarcophagi.